FLEXiO 690 Sprayer

$ 189.99
The FLEXiO® 690 stationary system puts the weight on the ground for extended spraying comfort. It can paint a wall 11 times faster than a brush or put a fine finish on furniture, saving time and effort.

The FLEXiO 690 comes complete with two nozzles, one for big surface projects like walls, ceilings, siding and fences and the other for small projects and fine finishing on cabinets and trim. The turbine sits on the ground delivering air power through the hose to spray unthinned coatings with adjustable control, full coverage and low overspray.

Cleaning is faster than a brush or roller with a few removable parts that rinse clean, and the provided bag stores the hose and nozzles.

Covers an 8’x10’ surface in minutes:
-Stain: 1 minute
-Latex: 5 minutes


FLEXiO 690 Setup
FLEXiO 690 Setup Video
FLEXiO 690 Spraying
FLEXiO 690 Spraying Video


  • Covers an 8’ x 10’ surface in one to five minutes and can spray up to 8.2 gallons per hour
  • X-Boost Base 15' air hose provides painting comfort
  • Innovative iSpray nozzle provides fast coverage and can spray unthinned paints
  • Pattern adjustment can be horizontal or vertical and wide or narrow
  • Detail finish nozzle for small projects and fine finishes
  • Adjustable paint flow to match covering speed and project size

Parts and Accessories

P/N 0529224
Air Cap for iSpray Front End (Black Needle)

Air Cap for iSpray Front End (Black Needle)

Buy Now
P/N 0529225
Spray Jet Kit for iSpray Front End

Spray Jet Kit for iSpray Front End

Buy Now
P/N 2343747
Nozzle for iSpray Front End (Black Needle)

Nozzle for iSpray Front End (Black Needle)

Buy Now
P/N 0529005
Check Valve Kit for iSpray, Control Finish and Detail Front Ends

Check Valve Kit for iSpray, Control Finish and Detail Front Ends

Buy Now
P/N 0417465
Nozzle Gasket for iSpray Front End (Black Needle)

Nozzle Gasket for iSpray Front End (Black Needle)

Buy Now
P/N 2303366
1.5 Quart Cup for iSpray Front End

1.5 Quart Cup for iSpray Front End

Buy Now
P/N 0529013
Detail Finish Front End

Detail Finish Front End

Buy Now
Flexio 690 Sprayer is rated 3.9 out of 5 by 11.
Rated 5 out of 5 by from excellent sprayer used with very thick paint and covered and worked very well in any surface
Date published: 2019-08-07
Rated 2 out of 5 by from Only good for one round of paint My stick handle on my roller broke so I decided to go ahead and just buy a sprayer kit. I went with this one because of the easy handling. Well it worked just fine until I had to refill. Once you refill BAM paint everywhere out the side in globs. Turns out the paint dries inside the nozzle so you have to completely take the front end apart between each use. Wagner, seriously is this product worthless or am I missing something... or maybe just not designed for latex paint.
Date published: 2017-05-20
Rated 5 out of 5 by from Easy to use, easy to clean I used the Flexio 690 to stain a lattice fence and lattice wall under my pool deck. It took me 50 minutes to stain and 15 minutes to clean up and put back together. It gave a nice even finish and I only needed to put on one coat. On the 4X4 posts of the lattice fence, I used a brush to even it out and prevent any running of the stain. Next time I have a staining project, I won't put it off because this product makes it so much quicker and easier.
Date published: 2016-06-14
Rated 1 out of 5 by from Not high quality just doesn't work This sprayer flat out doesn't work. If you're looking for detailed professional paint job this is not it. No matter what I did even dinning the material beyond recommendation it would still splatter and not paint and even finish
Date published: 2016-04-04
Rated 1 out of 5 by from Storage Bag NOT Big Enough I will change my review once I have actually tried the product. However, WAGNER YOU NEED TO MAKE THE STORAGE BAG BIGGER! I have tried a few different configurations and while everything will fit, it will not zip closed. Engineers, go back to the drawing board and send me a bag that is functional.
Date published: 2015-10-30
Rated 4 out of 5 by from Painted my privacy fence in no time! Yesterday I stained the inside of my privacy fence (6ft x 8ft panels and I have 25 panels to stain, including the posts). it only took me 3 hours to stain 25 panels and that is including a 30 minute lunch break. So actually it only took me 2 and a half hours to paint 25 panels. My only gripe is cleaning the gun and all the small parts that remove from the gun. I'm sure all spray guns are a pain to clean, and I am very thorough on cleaning my tools and ensuring they work for many years to come. Even with staining the fence and then cleaning I only spent about 3.5-4 hours total. I will continue my job on the next nice day I have to see how the flexio 690 will hold up after the cleaning. I will update this post or post another review of the product if I have any troubles, but I don't anticipate having any issues. I would definitely recommend this product to a friend. My only reason for not giving this product an "excellent" review is due to the time spent cleaning and the plastic movable pieces that seem fragile, especially the trigger which needs to be removed to clean the handle well.
Date published: 2015-04-20
Rated 5 out of 5 by from For a professional look the Wagner Flexio 690 is exactly what you want. The Wager Flexio 690 is a jewel to work with. It is light weight and very balanced with paint in the container which makes it easy to use and handle. It has very little over-spray. My husband and I were painting a bathroom vanity, 4 drawers, 3 doors and the vanity box. I hate paint brush/roller marks so I thought a sprayer would be the way to go. I had purchased another sprayer which was a disaster, dumped paint everywhere and then I had to start from scratch after removing the mess the first sprayer made. Needless to say I was not happy about starting a project over and having to remove paint from my doors and drawers. I decided to try another sprayer and use the Flexio 690, I am so happy I did, as this paint sprayer did a wonderful job. The sprayer comes with a nice storage case and 2 containers. One for detailed work and one for general painting. You do not have to thin latex paint to use this sprayer. The sprayer was very easy to use. Set up is stress-free, just pour your paint in the container check your settings and start painting. Practice first on a piece of cardboard or use the paper instructions which are included in the box to get familiar with handling the sprayer. After our practice session we found the Wagner 690 sprayed a nice even pattern which was easily maintained with no drips or runs. We did use a high grade advanced paint which gave our project a profession look. Start your painting project by pulling the trigger half-way this starts the motor, and then pull the trigger all the way to start painting. The direction of the paint can be adjusted to control the amount of material and width. The instructions said you can also paint ceilings, which will be a big plus down the line for us. We hate painting ceilings. If you experience any problems call their customer service line they provide immediate help. Wagner provides very detailed directions on how to clean the sprayer. Their instructions are clear and concise. Cleaning is easy but can be time consuming. I wanted to make sure everything was cleaned well as we had several coats of paint to spray on and the weather was not cooperating with us. Make sure that the suction tube is cleaned out well. The cleaning did go faster after each use. In conclusion, after priming, and painting 3 coats of paint I would highly recommend the Wagner 690 paint sprayer, it provides a high end finish and easy to use. After seeing how great the Flexio 690 preformed, we are contemplating painting our kitchen cabinets which will be a big job, and which I had no intention of starting. But the upgrade will be worth it in the end. We also have 2 rooms to paint and since the over-spray was minimal I will not hesitate to use the paint sprayer in the house.
Date published: 2014-12-11
Rated 5 out of 5 by from We're moving and I've been painting like crazy Bought the Wagner 690 hoping to easy my pain, because I have to tell you I'd rather pay taxes than paint! Get the picture? I hate painting! I have 12 rooms to paint most of the will require 2 or 3 coats because my wife and I love exotic colors but real estate agents hate them I did the first 2 rooms with a roller, OMG I rather step on a bees nest in bare feet. Bought the Wagner 690 and have painted 4 room with the little gadget and while there are hundreds of things I'd rather be doing besides painting, I can at least say now I'd rather paint than pay taxes or get stung by bees. I've read a million review and I have to say anytime the machine didn't work right WAS MY FAULT. It only happen twice, once I did not tighten the nut on the end of the nozzle and as advertised it made a big mess. The 2nd time I had refiled the paint jar and laid the nozzle assembly down upside down so it wouldn't drip. That must be a no-no, because when I put it back in service it didn't wok well. Regardless in both cases all I did was clean the nozzle as directed and that resolved any problems I caused.
Date published: 2014-06-27
  • y_2020, m_5, d_26, h_14
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.8
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_11
  • loc_en_US, sid_024964219322, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_wagnerspraytech
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 203.77ms

I'm painting a tractor. Taking parts off and painting them separately. Presently using aerosol cans but would like to try an airless sprayer. Will the Flexio 690 sprayer work for this? Using Iron Guard, Case IH enamel, IH 2150 Red; and MS43 Gray Primer.

Asked by: Farmer 1
We have another line of HVLP sprayers that may work better for you. Take a look at the MotoCoat here -https://www.wagnerspraytech.com/products/paint-sprayers/motocoat-complete-auto-paint-sprayer/ and also at this one here - http://www.rockler.com/earlex-hv6003pus-hvlp-sprayport Which is a professional system for the best results. For more info call us at 800-328-8251.
Answered by: Wagner
Date published: 2018-02-07

Will this handle stain and polyurethane without diluting either one?

Asked by: Kenn
Depending on the stain and which front end you use you shouldn't have any problems. Make sure they are mixed up well and strained. If you would like to call us at 1-800-328-8251 with what type of stain you will spray we will assist you with any questions you have.
Answered by: Wagner
Date published: 2017-12-18

How do you store the Flexio 690 for long period of time? Is it ok to use Graco Pump fluid and follow those directions?

Asked by: trey
With this unit being a HVLP(High Volume Low Pressure) sprayer you don't need to use any specific fluid for long term storage like you would for an airless sprayer. You would want to follow the cleaning instructions in the manual before putting into storage. Please reach out to our technical support staff at 1(800)328-8251 if you have any other questions or needs.
Answered by: Wagner
Date published: 2017-10-25

I need to paint the interior of my home including ceilings. What is the best model and can will it be able to have a suction tube for a 1 gallon can?

Asked by: damor1955
The Flexio 690 is an excellent choice for painting ceilings, but if you want to draw paint directly from the paint can look at the Flexio 970, which does exactly that! Good luck with your projects.
Answered by: Wagner
Date published: 2017-10-20

How do you clean the sprayer after using a stain?

Asked by: Marian
You should spray the appropriate cleaning solution through the sprayer and take the front end pieces apart and clean them with the appropriate cleaner. Expanded cleaning instructions can be found in the owner's manual starting on page 12 and you can watch some video's at this link, https://www.wagnerspraytech.com/products/paint-sprayers/flexio-690-paint-sprayer/. If you would like to discuss this or have any questions fee free to call us at 1-800-328-8251.
Answered by: Wagner
Date published: 2017-10-03

Power frequency? Can use in Philippines? 50-60hz

Asked by: Joel mendoza
Our sprayers run off our 60hz power supplies but are designed to be use in North America on their 120v systems. Please reach out to technical support staff at 1(800)328-8251 if you have any other questions or needs.
Answered by: Wagner
Date published: 2017-08-12

need compressor

The Flexio 690 comes with everything needed to spray in the box. You just need to plug it in and adjust some settings and such depending on the material you are spraying. Please contact our technical support staff at 1(800)328-8251 if you have any other questions or needs.
Answered by: Wagner
Date published: 2017-08-03

Can interior latex gloss paint be run through this machine? I need to paint 8 doors.

Asked by: na001
Yes it can. Use the detail front end, thin the paint 10% with water, add flow agent too. Lay the doors down and spray down on them, gravity will help get a better finish. Stand the doors up and gravity makes it harder to get a nice finish. For more technical support contact us at 800-328-8251.
Answered by: Wagner
Date published: 2017-08-01

Using the 690 to paint a "normal sized" room wall, painting with paint/primer, about how often do you have to refill the container? I am trying to decide between 690 and 970.

Asked by: Mjowens
The iSpray front end that comes with the Flexio 690 that is designed for spraying wall will cover and a 10 x 10 FT until you have to refill the cup. Please contact our technical support department at 1(800)328-8251 if you have any other questions or needs.
Answered by: Wagner
Date published: 2017-07-15

In addition to handling unthinned oilbase and latex paints will the Flexio 690 and Flexio 890 handle Linseed oil and other oils for wood treating protection?

Asked by: normjolsen
As long as your material cleans up with either warm soapy water, for water-based, or mineral spirits, for oil-based, and has a flash point above 100 degrees you should be able to spray it. Please call our technical support staff at 1(800)328-8251 if you have any other questions or needs.
Answered by: Wagner
Date published: 2017-07-07

I'm wondering just how extensive the overspray might be. Will this require extensive masking and taping for indoor use, or is control fine enough that it isn't necessary?

Asked by: jim p
When spraying inside a home where people live, there is no sprayer made that won't cause you to mask and tape areas off. With HVLP(High Volume Low Pressure), like the 690, overspray is minimized, but there still is some. With practice you can learn to control the overspray even better through proper adjustment and thinning of product. For an in depth discussion call us at 800-328-8251.
Answered by: Wagner
Date published: 2017-06-21

i just purchased a wagner flexio 690. i used it two times with satisfactory results. However, after filling it for the third time, it completely quit priming paint into the gun. I've looked at the troubleshooting guide and can't seem to figure it out.

Asked by: Brian R
If you are using the iSpray front end it's most likely a clog in an air passage. On the suction tube, just below the white cup gasket, you will find a very small hole that most likely has paint in it. Use a paper clip or toothpick to clear it out and test your sprayer with water. You're always welcome to contact us at 800-328-8251.
Answered by: Wagner
Date published: 2017-05-31

Plan on using HVLP 690 Detail Front End to spray Behr Premium Ultra Plus Satin Enamel on wooden dining chairs & table.

Any Issues with this Behr paint? Any tips on starting parameters.....thin with distilled water at what %? ..... add Floetrol at what %? ....other ideas?
Asked by: Yaks
Thin 10% with water. Add 1 ounce of Floetrol per quart also. Adjust the spray to get maximum flow with minimum spit and spray from 6" away from the project. For more help or details call technical support at 800-328-8251.
Answered by: Wagner
Date published: 2017-05-24

What is the country of origin for this sprayer?

I asked before and was given the answer of the location of your company. I know where your company is located, what i want to know is where are the paint sprayers made. Is it made in China, Mexico, USA? Somewhere else? Thank you for your help.
Asked by: curious2
Our products are manufactured in different locations. The Flexio 690 is manufactured in China. If you have other questions please feel free to call us at 1-800-328-8251.
Answered by: Wagner
Date published: 2017-04-21

What country is the sprayer made on

I may have missed it but cannot find it in the product details. Just wondering what country it is made in.
Asked by: curious2
We are located in Minneapolis, MN, USA.
Answered by: Wagner
Date published: 2017-04-19

Why does it start spraying paint as soon as I turn on the power?

I am new to using the 690. First day's usage it worked great. Now it begins spraying paint as soon as I turn on the power and prior to pulling the trigger. I am using the Ispray with latex paint. Frustrating while trying to paint kitchen cabinets.
Asked by: Scooter
It sounds like there may be some paint slowing down the needle that closes off the nozzle, preventing spray. Check to make sure everything is clean and that the ring that holds everything together on the front end is tight. If this continues, contact technical support at 800-328-8251.
Answered by: Wagner
Date published: 2017-02-07

Can the Flexio 690 model be used with chalk paint?

Asked by: Nuke
Yes the Flexio 690 can be used to spray chalk paint. We suggest using the Detail Front end instead of using the iSpray Front end for spraying the chalk paint. The iSpray Front end will spray unthinned materials including latex paint and is ideal for projects such as spraying walls, small buildings, fences etc... and will provide a roller-like, or slightly stippled finish. The Detail Front end is best used on your fine finish projects such as spraying cabinets, furniture, doors, trim etc. and will provide a smoother, finer finish than the iSpray Front end. Depending on the chalk paint, the Detail Front end may require some thinning in order to spray properly. If you have any other questions feel free to call us at 1-800-328-8251
Answered by: Wagner
Date published: 2016-10-03

I have a couple of rooms to paint and popcorn ceilings that need some special attention. Can I use oil based and latex?

Would there be any problem using this to undercoat with oil based and overcoat with latex based?
Asked by: TBuck
The Flexio line can handle both oil based and latex paints. Remember to only tilt the gun back to about 60 degrees at the ceiling, never straight up. More than 60 can send paint backwards into the turbine and possibly burn out the motor. Be sure and clean at the end of the day using water and/or mineral spirits.
Answered by: Wagner
Date published: 2016-07-26

Whats the difference between the 690 and 590

Is there any difference apart from the 590 is more of a gun type. Is this the only difference?
Asked by: stephencaso
The Flexio 590 is a handheld sprayer that comes with an iSpray Front end, a Detail Front end, and a carrying case. The Flexio 690 comes with the iSpray Front end, the Detail Front end, a 15ft hose, and a storage bag for the hose and front ends. The 590 has a two stage trigger so you pull the trigger slightly to start the turbine before pulling all the way to spray your material. The 690 has a constant flow of air as soon as the turbine is turned on and will spray when you pull the trigger on the front end. Because the motor is directly attached to the front end on the Flexio 590 it cannot be tilted upward at more than a 45 degree angle but the Flexio 690 can be. Both Flexio’s have the same size motor, material and flow controls. If you would like further assistance feel free to call us at 1-800-328-8251 and we will assist you.
Answered by: Wagner
Date published: 2016-12-12

Anyway to avoid "orange peel" with acrylic interior/exterior paint?

I just bought this tool and plan to use it for various things (stain on small wood projects, paint on other things etc). I noticed it says it produces an orange peel like finish perfect for interior walls (like a roller). Any way if I'm painting say outdoor rocking chairs and a white high gloss acrylic to avoid that? I know I can't put the material through the detail sprayer per the manual but I'm wondering if I can get a smooth finish? thanks!
Asked by: watson524
For a "finer" finish, use the "detail" front end. Thin the paint about 10% with water, also add a flow agent, such as Floetrol (2oz per quart of paint). Spray from 6" from the project and adjust the flow so there is no spit. If it is spitting, you have too much paint flow. If you have other questions please call us at 800-328-8251
Answered by: Wagner
Date published: 2016-05-26

can i buy a carry bag for (688-690)?

I'd like to keep I-sprayer all together in one bag!!
Asked by: mall
If you contact our office in the UK they can let you know if there is one available. The email address is enquiries@wagner-group.com.
Answered by: Wagner
Date published: 2016-05-09

Can the 690 be used to spray latex paint on exterior stucco walls ?

Asked by: redryder
Absolutely it can, using the iSpray front end with latex should work great for stucco walls.
Answered by: Wagner
Date published: 2016-03-29

I am not interested in spraying bed liners so if I had a longer hose would the Flexio 690 work for automotive paint?

I read the question about the difference between the Motocoat and Flexio 690. I only would be interested in spraying automative paint and not bedliners or peelable dip coatings. Would the Flexio 690 with a longer hose to put outside the work area work for this application?
Asked by: Gary911
Neither the Flexio 690 nor the MotoCoat will produce a showroom-grade finish that you would generally desire with an automotive paint. The 690 will also only be compatible with water and oil-based coatings that clean up with soap and water or mineral spirits.
Answered by: Wagner
Date published: 2015-11-10

What's the difference between motocoat and flexio 690?

I'd like to get this one because I'll use it to paint doors and walls but in the future I'd like to try with the car. Can I use it for that? I want a sprayer for all purpose, DIY. Thanks
Asked by: Pablo
The MotoCoat has a spark-contained turbine to ensure compatibility with bedliners and peelable "dip" coatings. The hose is also longer to allow the turbine to be placed outside of the work area. The 690 is not compatible with those types of coatings.
Answered by: Wagner
Date published: 2015-08-13

Benjamin Moore advance paint ( alkalyed ) ok to use?

Asked by: Jacko
Water-based paint should work just fine in the Flexio 690, with or without thinning.
Answered by: Wagner
Date published: 2015-04-23

what type of grease/lube should I use to grease the o-rings on my flexio 690?

Asked by: whittyrebel
Use a thin layer of petroleum jelly to lubricate the O-ring. If you have any other questions please feel free to call us at (800)328-8251.
Answered by: Wagner
Date published: 2015-04-20

will the 690 use water based primer?

Asked by: jbk8787
The Flexio 690 should be able to spray a water-based primer without issue.
Answered by: Wagner
Date published: 2015-04-15

What other screw top jars is this compatible with?

I have a couple colors of paint that I use in small batches and I would like to store them in jars that I could then attach to the sprayer and switch quickly using an extra to clean between the different colors so I don't have to clean the jars each time I switch.
Asked by: Melissa
We do not have any containers for this unit that have available lids. You will need to store the paint in a separate container and pour it in as you need it.
Answered by: Wagner
Date published: 2015-02-17

will thw 690 spray polyurethane for wood working finishes

Asked by: markt
The Flexio 690 will spray both water and oil-based materials requiring cleanup with soap and water or mineral spirits. With the included Detail Front End, it will produce a fine finish for woodworking.
Answered by: Wagner
Date published: 2016-05-23

Are there any special techniques for painting ceilings / overhead?

Asked by: C5Engr
There are no real differences between how you'd typically spray straight ahead (ex:a wall) vs. how you'll spray a ceiling. The 690 can be sprayed straight up towards a ceiling. As with typical spraying, you'll overlap your spray pattern roughly 50% to achieve even coverage.
Answered by: Wagner
Date published: 2015-09-13
  • y_2020, m_5, d_26, h_14CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.8
  • cp_2, bvpage2n
  • co_hasquestionsanswers, tq_39
  • loc_en_US, sid_024964219322, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_wagnerspraytech
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 167.06ms
Stay Connected

Find out what’s new from Wagner including product news, exclusive email offers, promotions and more.